SilCool TIA216G is a silicone thermal potting from Momentive, rated 1.6 W/m·K. Typical uses: Heat dissipation and insulating potting of electrical/electronic parts; soft rubber/gel stress relief. Short answer: we dispense it with PDP-5000HF + recirculating feed.
Recommended: PDP-5000HF + recirculating feed, fed from a 20 L pail.
Material at a glance
| Manufacturer | Momentive |
|---|---|
| Type | Thermal potting |
| Chemistry | Silicone |
| Thermal conductivity | 1.6 W/m·K |
| Mix ratio | 1:1 by weight |
| Viscosity | Part A 9 Pa·s, Part B 7 Pa·s, mixed 8 Pa·s |
| Cure | 0.5 h at 70 °C or 6 h at room temp; work time 0.5 h |
From the manufacturer's published data (source). Always work from the current technical data sheet.
How we dispense it
We have run SilCool TIA216G on Dispense Robotics equipment. Our recommendation is PDP-5000HF + recirculating feed, fed from a 20 L pail. Pump size still depends on your shot or bead size and cycle time, so send us those and we'll confirm.
- Abrasion: the ceramic filler that carries the heat wears pumps out. We use tungsten carbide rotors and wear-resistant stators and run the pump slowly, at 8 to 12 rpm, for long wear life.
- Ratio: each side is metered by its own progressive cavity pump to within ±1%. Check ratio by weighing a shot from each side every week, because filled materials vary from batch to batch.
- Mixing: a disposable static mixer does the mixing. Purge or change it before the material's working life runs out.
- Settling: heavy filler settles in the pail. Keeping the material agitated and recirculating, all the way to the pump, gives every pour the same filler content, and vacuum degassing keeps air out of the part.
See our PDP two-component metering pumps and the Material Feeding System (MFS), or use the pump configurator.
How the MFS keeps filler in suspension
The Material Feeding System agitates and recirculates the material so heavy filler stays mixed all the way to the pump. Watch how it circulates the product:
Frequently asked questions
What pump should I use to dispense SilCool TIA216G?
We have run SilCool TIA216G on Dispense Robotics equipment. Pump size depends on your shot or bead size and cycle time; send us those and we will size it.
Can SilCool TIA216G be fed from pails or drums?
Yes. For production volumes we feed it from bulk containers through a Material Feeding System (MFS), which agitates and recirculates the material so the filler stays in suspension, and degasses it under vacuum.
How do you keep SilCool TIA216G on ratio?
Each side is metered by its own progressive cavity pump, held to within ±1% per side. We recommend a weekly check: weigh a shot from each side and adjust, because filled materials vary from batch to batch.
Will SilCool TIA216G wear out the pump?
Thermally conductive fillers are abrasive. With tungsten carbide rotors, wear-resistant stators and pump speeds of 8 to 12 rpm, stators typically last 6 to 12 months and rotors up to 24 months, and a pump rebuild takes under an hour.
Talk it through with us
Running SilCool TIA216G, or about to? Send us the technical data sheet, your bead or shot size and your cycle time, and we'll recommend a pump and feed system. We can run an application test on your material before you buy. Contact us
Related materials
- SilCool TIA211G · Momentive, thermal potting
- SilCool TIA227G · Momentive, thermal potting
- SilCool TIA208RL · Momentive, thermal potting
- CoolTherm EP-2000 · Parker LORD, thermal potting / encapsulant
- CoolTherm EP-3500 · Parker LORD, thermal potting / encapsulant
- CoolTherm SC-320 · Parker LORD, thermal potting / encapsulant
All thermal interface materials · Materials we've dispensed
SilCool TIA216G is a trademark of Momentive or its affiliates. Dispense Robotics is not affiliated with the manufacturer; the name is used to describe the material our equipment dispenses.