SikaForce-326 CB is a polyurethane 2K thermal adhesive from Sika, rated 1.2 W/m·K. Typical uses: Cell to cooling plate (cell-to-pack); structural, flame retardant. Short answer: we dispense it with a PDP two-component progressive cavity metering pump with a static mixer.
Material at a glance
| Manufacturer | Sika |
|---|---|
| Type | 2K thermal adhesive |
| Chemistry | Polyurethane |
| Thermal conductivity | 1.2 W/m·K |
| Mix ratio | 1:1 by volume and weight |
| Viscosity | Paste |
| Cure | Room temperature, heat-accelerable; pot life 30 min |
| Packages | 400 ml dual cartridge; 23 l pails; 195 l drums |
From the manufacturer's published data (source). Always work from the current technical data sheet.
How we dispense it
For a two-component thermally conductive adhesive we start with a PDP two-component progressive cavity metering pump and a disposable static mixer, fed from dual cartridges for lab and low volume, or from pails with a follower-plate pail pump for production. Pump size depends on your shot or bead size and cycle time.
- Abrasion: the ceramic filler that carries the heat wears pumps out. We use tungsten carbide rotors and wear-resistant stators and run the pump slowly, at 8 to 12 rpm, for long wear life.
- Ratio: each side is metered by its own progressive cavity pump to within ±1%. Check ratio by weighing a shot from each side every week, because filled materials vary from batch to batch.
- Mixing: a disposable static mixer does the mixing. Purge or change it before the material's working life runs out.
See our PDP two-component metering pumps, or use the pump configurator.
Frequently asked questions
What pump should I use to dispense SikaForce-326 CB?
For a two-component thermally conductive adhesive we start with a PDP two-component progressive cavity metering pump and a disposable static mixer, fed from dual cartridges for lab and low volume, or from pails with a follower-plate pail pump for production. Pump size depends on your shot or bead size and cycle time; send us those and we will size it.
Can SikaForce-326 CB be fed from pails instead of cartridges?
Sika lists these packages: 400 ml dual cartridge; 23 l pails; 195 l drums. Cartridges suit lab and low volume. Above that, a follower-plate pail pump feeds the metering pump directly, which cuts container changes and waste.
How do you keep SikaForce-326 CB on ratio?
Each side is metered by its own progressive cavity pump, held to within ±1% per side. We recommend a weekly check: weigh a shot from each side and adjust, because filled materials vary from batch to batch.
Will SikaForce-326 CB wear out the pump?
Thermally conductive fillers are abrasive. With tungsten carbide rotors, wear-resistant stators and pump speeds of 8 to 12 rpm, stators typically last 6 to 12 months and rotors up to 24 months, and a pump rebuild takes under an hour.
Talk it through with us
Running SikaForce-326 CB, or about to? Send us the technical data sheet, your bead or shot size and your cycle time, and we'll recommend a pump and feed system. We can run an application test on your material before you buy. Contact us
Related materials
- Sikaflex-961 TC · Sika, 2K thermal adhesive
- SikaForce-325 CB · Sika, 2K thermal adhesive
- SikaFast-606 TC · Sika, 2K thermal adhesive
- BERGQUIST LIQUI BOND TLB SA2000 (Liqui-Bond SA 2000) · Henkel Bergquist, 1K thermal adhesive
- LOCTITE TLB 9300 APSi · Henkel Loctite, 2K thermal adhesive (structural, EV battery)
- LOCTITE TLB 9270APS · Henkel Loctite, 2K thermal adhesive (EV battery)
All thermal interface materials · Materials we've dispensed
SikaForce-326 CB is a trademark of Sika or its affiliates. Dispense Robotics is not affiliated with the manufacturer; the name is used to describe the material our equipment dispenses.