LOCTITE TLB 9270APS is an urethane 2K thermal adhesive (EV battery) from Henkel Loctite, rated 2 W/m·K. Typical uses: Battery cells to cooling plate bonding; heat-sensitive components in EV battery systems. Short answer: we dispense it with a PDP two-component progressive cavity metering pump with a static mixer.
Material at a glance
| Manufacturer | Henkel Loctite |
|---|---|
| Type | 2K thermal adhesive (EV battery) |
| Chemistry | Urethane |
| Thermal conductivity | 2 W/m·K |
| Cure | Fast curing (no schedule stated); long working time |
| Packages | 400 cc cartridges; 16 L pail kits; 140 L drum kits |
From the manufacturer's published data (source). Always work from the current technical data sheet.
How we dispense it
For a two-component thermally conductive adhesive we start with a PDP two-component progressive cavity metering pump and a disposable static mixer, fed from dual cartridges for lab and low volume, or from pails with a follower-plate pail pump for production. Pump size depends on your shot or bead size and cycle time.
- Abrasion: the ceramic filler that carries the heat wears pumps out. We use tungsten carbide rotors and wear-resistant stators and run the pump slowly, at 8 to 12 rpm, for long wear life.
- Ratio: each side is metered by its own progressive cavity pump to within ±1%. Check ratio by weighing a shot from each side every week, because filled materials vary from batch to batch.
- Mixing: a disposable static mixer does the mixing. Purge or change it before the material's working life runs out.
See our PDP two-component metering pumps, or use the pump configurator.
Frequently asked questions
What pump should I use to dispense LOCTITE TLB 9270APS?
For a two-component thermally conductive adhesive we start with a PDP two-component progressive cavity metering pump and a disposable static mixer, fed from dual cartridges for lab and low volume, or from pails with a follower-plate pail pump for production. Pump size depends on your shot or bead size and cycle time; send us those and we will size it.
Can LOCTITE TLB 9270APS be fed from pails instead of cartridges?
Henkel Loctite lists these packages: 400 cc cartridges; 16 L pail kits; 140 L drum kits. Cartridges suit lab and low volume. Above that, a follower-plate pail pump feeds the metering pump directly, which cuts container changes and waste.
How do you keep LOCTITE TLB 9270APS on ratio?
Each side is metered by its own progressive cavity pump, held to within ±1% per side. We recommend a weekly check: weigh a shot from each side and adjust, because filled materials vary from batch to batch.
Will LOCTITE TLB 9270APS wear out the pump?
Thermally conductive fillers are abrasive. With tungsten carbide rotors, wear-resistant stators and pump speeds of 8 to 12 rpm, stators typically last 6 to 12 months and rotors up to 24 months, and a pump rebuild takes under an hour.
Talk it through with us
Running LOCTITE TLB 9270APS, or about to? Send us the technical data sheet, your bead or shot size and your cycle time, and we'll recommend a pump and feed system. We can run an application test on your material before you buy. Contact us
Related materials
- LOCTITE TLB 9300 APSi · Henkel Loctite, 2K thermal adhesive (structural, EV battery)
- BERGQUIST LIQUI BOND TLB SA2000 (Liqui-Bond SA 2000) · Henkel Bergquist, 1K thermal adhesive
- CoolTherm UR-2000 · Parker LORD, 2K gap filler / thermal adhesive
- CoolTherm TC-2002 · Parker LORD, 2K thermal adhesive (structural)
- DOWSIL TC-2035 CV Thermally Conductive Adhesive · Dow, 2K thermal adhesive
- DOWSIL SE 4486 CV Thermally Conductive Adhesive · Dow, 1K thermal adhesive
All thermal interface materials · Materials we've dispensed
LOCTITE TLB 9270APS is a trademark of Henkel Loctite or its affiliates. Dispense Robotics is not affiliated with the manufacturer; the name is used to describe the material our equipment dispenses.