THERM-A-GAP CIP 35E is a 2K gap filler / cure-in-place from Parker Chomerics, rated 3.5 W/m·K. Typical uses: Energy storage; power electronics; consumer electronics; commercial/industrial devices. Short answer: we dispense it with a PDP two-component progressive cavity metering pump with a static mixer.
Material at a glance
| Manufacturer | Parker Chomerics |
|---|---|
| Type | 2K gap filler / cure-in-place |
| Thermal conductivity | 3.5 W/m·K |
| Mix ratio | 1:1 |
| Viscosity | ~200,000 cP each part (Brookfield HB-7, 25 rpm, ASTM 2196); working life 6 h |
| Cure | 24 h @ 25 °C, 120 min @ 80 °C, or 30 min @ 125 °C |
| Packages | 45 cc, 200 cc, 400 cc cartridges; 600 cc (2x300 cc); 1200 cc (2x600 cc); 5,000 cc (2x1 gal); 16,600 cc (2x5 gal) |
From the manufacturer's published data (source). Always work from the current technical data sheet.
How we dispense it
For a two-component gap filler we start with a PDP two-component progressive cavity metering pump and a disposable static mixer, fed from dual cartridges for lab and low volume, or from pails with a follower-plate pail pump for production. Pump size depends on your shot or bead size and cycle time.
- Abrasion: the ceramic filler that carries the heat wears pumps out. We use tungsten carbide rotors and wear-resistant stators and run the pump slowly, at 8 to 12 rpm, for long wear life.
- Ratio: each side is metered by its own progressive cavity pump to within ±1%. Check ratio by weighing a shot from each side every week, because filled materials vary from batch to batch.
- Mixing: a disposable static mixer does the mixing. Purge or change it before the material's working life runs out.
- Dispense pattern: gap fillers are squeezed between the part and the housing, so the pattern (dots, lines or a star) decides coverage and whether air gets trapped.
See our PDP two-component metering pumps, or use the pump configurator.
Frequently asked questions
What pump should I use to dispense THERM-A-GAP CIP 35E?
For a two-component gap filler we start with a PDP two-component progressive cavity metering pump and a disposable static mixer, fed from dual cartridges for lab and low volume, or from pails with a follower-plate pail pump for production. Pump size depends on your shot or bead size and cycle time; send us those and we will size it.
Can THERM-A-GAP CIP 35E be fed from pails instead of cartridges?
Parker Chomerics lists these packages: 45 cc, 200 cc, 400 cc cartridges; 600 cc (2x300 cc); 1200 cc (2x600 cc); 5,000 cc (2x1 gal); 16,600 cc (2x5 gal). Cartridges suit lab and low volume. Above that, a follower-plate pail pump feeds the metering pump directly, which cuts container changes and waste.
How do you keep THERM-A-GAP CIP 35E on ratio?
Each side is metered by its own progressive cavity pump, held to within ±1% per side. We recommend a weekly check: weigh a shot from each side and adjust, because filled materials vary from batch to batch.
Will THERM-A-GAP CIP 35E wear out the pump?
Thermally conductive fillers are abrasive. With tungsten carbide rotors, wear-resistant stators and pump speeds of 8 to 12 rpm, stators typically last 6 to 12 months and rotors up to 24 months, and a pump rebuild takes under an hour.
Talk it through with us
Running THERM-A-GAP CIP 35E, or about to? Send us the technical data sheet, your bead or shot size and your cycle time, and we'll recommend a pump and feed system. We can run an application test on your material before you buy. Contact us
Related materials
- THERM-A-GAP CIP 60 · Parker Chomerics, 2K gap filler / cure-in-place
- BERGQUIST GAP FILLER TGF 4000 · Henkel Bergquist, 2K gap filler
- BERGQUIST GAP FILLER TGF 3600 · Henkel Bergquist, 2K gap filler
- BERGQUIST GAP FILLER TGF 4400LVO · Henkel Bergquist, 2K gap filler (low volatility)
- BERGQUIST GAP FILLER TGF 4500CVO · Henkel Bergquist, 2K gap filler (controlled volatility)
- BERGQUIST GAP FILLER TGF 3500LVO · Henkel Bergquist, 2K gap filler (low volatility)
All thermal interface materials · Materials we've dispensed
THERM-A-GAP CIP 35E is a trademark of Parker Chomerics or its affiliates. Dispense Robotics is not affiliated with the manufacturer; the name is used to describe the material our equipment dispenses.