SilCool TIA141GF is a silicone 1K thermal gel (pre-cured putty) from Momentive, rated 4.1 W/m·K. Typical uses: Gap filling for complex shapes, 3D interfaces and non-uniform gaps; repairable. Short answer: we dispense it with a PCP progressive cavity pump.
Material at a glance
| Manufacturer | Momentive |
|---|---|
| Type | 1K thermal gel (pre-cured putty) |
| Chemistry | Silicone |
| Thermal conductivity | 4.1 W/m·K |
| Cure | non-curing (pre-cured; no cure required) |
| Packages | 300 ml cartridge |
From the manufacturer's published data (source). Always work from the current technical data sheet.
How we dispense it
For a single-component thermal gel we start with a PCP progressive cavity pump, fed from a cartridge for lab and low volume, or from a pail with a follower-plate pail pump for production. A progressive cavity pump meters by volume, so dot and bead size stay consistent. Pump size depends on your dot or bead size and cycle time.
- Abrasion: the ceramic filler that carries the heat wears pumps out. We use tungsten carbide rotors and wear-resistant stators and run the pump slowly, at 8 to 12 rpm, for long wear life.
- Feed: thick pastes don't flow to a pump on their own. Above cartridge volumes, a follower plate pushes the material out of the pail and keeps air out.
- Non-curing: there's nothing to purge, so the job is accurate, repeatable metering.
See our PCP progressive cavity pumps, or use the pump configurator.
Frequently asked questions
What pump should I use to dispense SilCool TIA141GF?
For a single-component thermal gel we start with a PCP progressive cavity pump, fed from a cartridge for lab and low volume, or from a pail with a follower-plate pail pump for production. Pump size depends on your shot or bead size and cycle time; send us those and we will size it.
Can SilCool TIA141GF be fed from pails instead of cartridges?
Momentive lists these packages: 300 ml cartridge. Cartridges suit lab and low volume. Above that, a follower-plate pail pump feeds the metering pump directly, which cuts container changes and waste.
Does SilCool TIA141GF need mixing?
No. It is a single-component material, so there is no mixer and no ratio to hold. The job is accurate, repeatable volumetric metering, which is what a progressive cavity pump does.
Will SilCool TIA141GF wear out the pump?
Thermally conductive fillers are abrasive. With tungsten carbide rotors, wear-resistant stators and pump speeds of 8 to 12 rpm, stators typically last 6 to 12 months and rotors up to 24 months, and a pump rebuild takes under an hour.
Talk it through with us
Running SilCool TIA141GF, or about to? Send us the technical data sheet, your bead or shot size and your cycle time, and we'll recommend a pump and feed system. We can run an application test on your material before you buy. Contact us
Related materials
- BERGQUIST LIQUI FORM TLF LF2000 (Liqui-Form 2000) · Henkel Bergquist, 1K thermal gel
- BERGQUIST LIQUI FORM TLF LF3500 (Liqui-Form 3500) · Henkel Bergquist, 1K thermal gel
- BERGQUIST LIQUI FORM TLF 6000HG · Henkel Bergquist, 1K thermal gel
- BERGQUIST LIQUI FORM TLF 10000 · Henkel Bergquist, 1K thermal gel
- THERM-A-GAP GEL 8010 · Parker Chomerics, 1K thermal gel
- THERM-A-GAP GEL 37 · Parker Chomerics, 1K thermal gel
All thermal interface materials · Materials we've dispensed
SilCool TIA141GF is a trademark of Momentive or its affiliates. Dispense Robotics is not affiliated with the manufacturer; the name is used to describe the material our equipment dispenses.